Nachi PCR-1B-05A-P-9297B 20/925541 swing motor for JCB 8014 8016 8018 Super mini excavator
If you decide to buy equipment at a low price, make sure that you communicate with the real seller. Find out as much information about the owner of the equipment as possible. One way of cheating is to represent yourself as a real company. In case of suspicion, inform us about this for additional control, through the feedback form.
Before you decide to make a purchase, carefully review several sales offers to understand the average cost of your chosen equipment. If the price of the offer you like is much lower than similar offers, think about it. A significant price difference may indicate hidden defects or an attempt by the seller to commit fraudulent acts.
Do not buy products which price is too different from the average price for similar equipment.
Do not give consent to dubious pledges and prepaid goods. In case of doubt, do not be afraid to clarify details, ask for additional photographs and documents for equipment, check the authenticity of documents, ask questions.
The most common type of fraud. Unfair sellers may request a certain amount of advance payment to “book” your right to purchase equipment. Thus, fraudsters can collect a large amount and disappear, no longer get in touch.
- Transfer of prepayment to the card
- Do not make an advance payment without paperwork confirming the process of transferring money, if during the communication the seller is in doubt.
- Transfer to the “Trustee” account
- Such a request should be alarming, most likely you are communicating with a fraudster.
- Transfer to a company account with a similar name
- Be careful, fraudsters may disguise themselves as well-known companies, making minor changes to the name. Do not transfer funds if the company name is in doubt.
- Substitution of own details in the invoice of a real company
- Before making a transfer, make sure that the specified details are correct, and whether they relate to the specified company.
Seller's contacts
+86 199 246...
Show
+86 199 2461 6345
China
China
Romania
Poland, Koziegłowy
Component: Main Hydraulic Swing Drive Motor Assembly
Manufacturer Model Number: Nachi PCR-1B-05A-P-9297B (PCR Series Architecture)
JCB OEM Part Numbers: 20/925541, 20925541
Machine Compatibility:
JCB 8014
JCB 8016 / Super
JCB 8018 / Super
Mini Excavator
Condition: Genuine Original New / Premium OEM Specification Equivalent
2. Technical Specifications
Motor Type: Fixed Displacement Axial Piston Swing Motor with Auxiliary Gear/Piston Architecture
Output Performance: Precision flow and torque profiles calibrated specifically for upper-structure rotation on JCB 1.4 to 1.8-ton mini excavators.
Integrated Control Network: Includes integrated dynamic braking check valves, anti-cavitation valves, and crossover relief valves to ensure smooth stopping and prevent boom drift.
Drive Configuration: Machined mounting flange with a precision output shaft designed for direct integration with the primary swing reduction gear or slew ring.
3. Critical Installation Requirements
Swing Motor Housing Priming (Mandatory)
Before starting the engine or engaging the swing control, pre-fill the swing motor casing with clean, fresh hydraulic fluid through its highest case drain port. Running an axial piston motor dry—even for a few seconds—will score the swash plate and piston slippers, causing immediate pressure loss.
Verify Case Drain Line Pressure
Inspect the low-pressure case drain hose back to the hydraulic oil reservoir. Ensure there are no sharp kinks, bends, or restrictions. High backpressure in the case drain line will blow out the main shaft seal.
Air Bleeding & Initial Startup Procedure
After mounting and priming, loosen the air bleed port on top of the motor housing. Crank the engine with fuel delivery disabled until clear, bubble-free hydraulic oil flows out, then re-tighten. Allow the machine to idle under no load for 10 to 15 minutes to purge remaining air from the circuit.
System Decontamination
If replacing a motor that suffered internal mechanical failure, drain and flush the hydraulic oil tank, flush lines leading to the main control valve, and clean the oil cooler. Always replace return and suction filters prior to initial startup.
4. Frequently Asked Questions (FAQ)
Q: Is the Nachi PCR-1B-05A-P-9297B a direct replacement for JCB part number 20/925541?
A: Yes. Nachi is the original hydraulic equipment manufacturer for these JCB mini excavator models. Part number 20/925541 cross-references directly to this Nachi PCR-1B unit with matching mounting dimensions, port thread specs, and shaft profiles.
Q: My JCB 8018 Super over-swings or drifts when working on an incline. Is the swing motor at fault?
A: Over-rotation, drifting under load, or jerky swing performance usually indicates that internal relief valves, anti-cavitation check valves, or wear plates inside the motor have degraded. Installing a replacement motor restores exact hydraulic braking and hold control.
Q: Does this unit arrive complete with integrated relief and brake valves?
A: Yes. The assembly comes complete with the valve manifold block pre-installed and factory-calibrated for immediate installation.
5. Shipping & Logistics
Packaging: Preserved with rust-inhibiting storage oil, fitted with heavy-duty port plugs, and packed inside an export-safe protective crate or box.
Transit Time: Global express air freight via DHL/FedEx/UPS typically delivers within 3 to 7 business days directly to your workshop or job site.